Harvesters break down to "six defenses"
Processing high-throughput samples, intelligent reuse for large-capacity publishing, work surface: 200cm, 8 sample injection needles, 12 temperature-controlled incubation positions, 12 room temperature incubation positions, 32 plate storage positions, Sunrise microplate reader, HydroFlex plate washer, up to 512 specimens, sequential loading of samples, reagents, microplates Parallel loading of up to 6 plates for fast dispensing.
The automatic enzyme immunoassay analyzer is based on the principle that the enzyme and the substrate can produce a color reaction, the absorption lines of different substances have different characteristics, and strictly abide by the Lambert-Beer law, quantitative and qualitative analysis of substances. instrument. The method of analyzing the content of various enzymes such as antigen or antibody generally mainly adopts colorimetric method. In practice, spectrophotometry is the basic working principle of an automatic enzyme immunoassay analyzer. The light emitted by the light source lamp becomes a beam of monochromatic light after passing through a filter or a monochromator. The monochromatic light beam passes through the sample to be tested in the microtiter plate, and part of the monochromatic light beam is absorbed by the sample and reaches the photodetector. The intensity of the light signal projected on it is converted into the magnitude of the electrical signal by the photodetector. This electrical signal is processed by pre-amplification, logarithmic amplification, analog-to-digital conversion, etc., and then sent to the microprocessor for data processing and calculation, and the test results are output by the display and printer. The microprocessor completes the movement in the X and Y directions of the mechanical drive through the control circuit. ELISA analyzer,enzyme immunoassay workstation,automatic enzyme immunoassay analyzer,automatic enzyme immunoassay system Jilin Sinoscience Technology Co. LTD , https://www.jlgkscience.com
Sun and rain
No matter what kind or model of harvester you are, regardless of the size of your body, you should have your own hangar. Some pilots save time by taking simple shelters or standing in the open air. The wind and rain will damage the body to varying degrees. Therefore, regardless of the type of harvester, you should try to cover the dedicated library.
Anti-dirt rust
After harvesting every quarter, the dirt, shredded grass, grains and other debris inside and outside the harvester should be completely removed, and the inside and outside of the harvester should be rinsed, dried and stored in the computer room. At the same time, the lubricating parts shall be cleaned, lubricated or sealed with oil. The parts where the protective paint falls off shall be timely painted and rustproof.
Anti-deformation decay
Improper storage of various transmission belts may cause mildew or deformation. After use, these parts should be removed, wiped and dried, stored in a ventilated place, and protected from insect or rat bites. All metal drive chains are washed with diesel oil or kerosene and dried, then put into oil for 15-40 minutes or soaked in oil overnight, and when the oil is not dripped, apply grease and wrap it in kraft paper. In a dry and ventilated place.
Anti rubber aging
The rubber and plastic products on the harvester are susceptible to aging and deterioration due to the effect of sunlight and ultraviolet rays, and they have poor elasticity and are easily broken. Therefore, when the rubber parts are stored, it is best to use hot paraffin oil on the surface of the rubber parts, and put them indoors where they are ventilated, dried, and exposed to direct sunlight.
Plastic deformation
Springs, belts, shanks, tires, etc., may be plastically deformed due to prolonged stress or improper placement. For this reason, some places need support, and wood can be used to lift the frame so that the tires are not under pressure. All the pressure springs are loosened, the belt is removed and stored separately, and the long shaft is removed to lay flat or hang vertically.
Loss of small items
Randomly used appliances, especially special tools and various spare parts, are best kept in registration, kept by special personnel, put back in place after use, and should not be placed after use.
The automatic enzyme immunoassay analyzer adds the sample to the microwells of the pre-coated antigen or antibody microtiter plate, washes after the reaction, removes the unseparated ligand, then adds the enzyme isolate, after incubation, washes again , remove the unseparated compound, and then add the enzyme substrate, after the reaction, the colored final product is formed, and the stop solution is added to stop the reaction. The absorbance of each microwell of the microtiter plate is read by the wavelength that has been set by the spectrophotometer. The concentration value of the analyte in the sample is calculated by the absorbance value of the sample and the standard curve, so that the quantitative result can be obtained, or the absorbance of the sample is compared with that of the standard product, so that the positive or negative qualitative result can be obtained.