Small mixer installation operation

Introduction:
The mixing part of the small mixer is a single-axis single-blade. The blade angle design on the single-blade is extremely reasonable and clever. When the single-blade rotates, the material rolls up and down, and the blades pass through the material, and a certain angle is pushed to the left and right sides of the mixing tank. The force makes it impossible for any corner material in the mixing tank to stand still, so that the materials are evenly mixed. This machine adopts the sealing method of end face sealing, adjusting sealing nut and compensating axial pressure. Practice has proved that the effect is better. The whole machine is sealed with stainless steel and meets GMP requirements.
Small mixer technical parameters:
â—† Working capacity: 10L/20L
â—† Mixing time: 5-20 rpm
â—† Pulp shaft speed: 24 rev / min
◆ The distance between the blade and the fuselage:              3mm
◆ Dropping method:                    Manual
◆ trough zui large dip:                140 degrees
â—†Production: 8 kg / time
â—† Power: 0.25kw/.55kw
◆Dimensions: 600×280×450mm
800 × 330 × 580mm
â—† Weight: 64kg/80kg
Small mixer instructions :
First, the machine uses
 
This machine is a horizontal trough single slurry mixer, which is mainly used for uniform mixing of dry or wet powders in different laboratories in the laboratory, and does not cause melting, volatilization or deterioration of materials during mixing.
This machine is also suitable for small batches of different main and auxiliary materials in the chemical, food, and other industrial sectors. It is not suitable for mixing semi-solid, liquid or excessively viscous materials.
 
Second, the structural characteristics
 
This machine is a complete machine base. The transmission system is flexible and balanced. The workpieces that are in contact with the mixing slurry and materials are made of stainless steel. It has good corrosion resistance and can maintain the quality of the mixture, so that it does not pollute or discolor. .
The transmission mechanism is mainly driven by worm gear and worm. It has no excessive noise when used, and has sufficient oil storage capacity to get good lubrication and improve the service life of the machine.
There is a spiral blade on the slurry shaft in the U-shaped trough to push the material for complex flow and achieve good mixing effect.
 
Third, the instructions for use
 
Before use, a dry run test should be carried out. Before the test, the firmness of all the coupling parts of the machine, the amount of lubricant of the reducer and the integrity of the motor equipment should be checked, and then the main switch of the power supply should be closed for the dry run test.
It is advisable to immerse the slurry shaft after the feeding. After the feeding, the trough cover should be covered and then driven to avoid the shallow discharge of the material. The cover is equipped with a mirror basket to observe the stirring condition of the material.
 
Fourth, the installation instructions
 
This machine is packed in the whole box. After unpacking, move it to the appropriate place, install the anchor bolts, evenly tighten the nuts of the anchor bolts, and then use the power cord.
 
Five, machine maintenance and repair
 
When used frequently, the gearbox must be replaced with new oil every three months. When replacing, the gearbox should be cleaned and new oil added.
The machine is regularly inspected 1-2 times a month. The inspection parts are worm gears, worms, bearings, oil seals. Whether the running parts are flexible and the fasteners are loose. If abnormal conditions are found, they should be dealt with in time.
During use, if abnormal vibration or abnormal sound is found, stop the inspection immediately.
Electrical control parts should be kept clean and sensitive, and faults should be repaired in time.
When the mixing slurry is assembled and disassembled, it should be lightly disassembled, stabilized and lightly placed to avoid deformation and damage.
After the use, the residual materials of all parts of the machine should be brushed. The long-term deactivation time is long. The machine must be wiped clean. The surface of the machine is coated with anti-rust oil and covered with a tarpaulin.

Hunan Zhongcheng Pharmaceutical Machinery Factory provides you with small mixers suitable for all pharmacies, clinics, pharmaceutical factories and hospitals. The quality is guaranteed, not satisfied with the return of seven days, one year warranty, lifetime maintenance, welcome new and old friends to log in to our company : Or directly : Consulting, our factory will provide you with more professional services!

Sushi ginger: Established in 2005,the  agricultural product deep processing department  covers an area of 230 acres, based on the Japanese sushi series, the domestic traditional Pickled Garlic, cucumber and radish series deep processing, to create a multi-variety  international professional cuisine manufacturer. After years of development, it has successfully achieved an average annual export more than 10,000 tons, and has become  leading company in export of pickled products. The company introduces advanced equipment such as slicers and X-ray foreign body detectors from Japan, with an annual production capacity of more than 30,000 tons, which fully meets needs of different customers for quality and delivery time. The pickled products have obtained HACCP, HALAL, BRC, Kosher and other international mainstream certifications. They are exported to more than 100 countries and regions such as Japan, the United States, and the European Union etc. ,and has been widely welcomed by domestic and foreign markets. 

1

235

Pickled Vegetables

Pickled Ginger Vegetables,Pickled Garlic Vegetables,Pickled Radish Vegetables,Pickled Cucumber Vegetables

Laiwu Manhing Vegetables Fruits Corporation , https://www.manhingfood.com